UQA38 Universal Quick Attach Plate – Skid Steer Coupler

Description

The UQA38 universal quick attach plate is a heavy-duty weld-on coupler plate for fabricating, repairing or converting attachments used with compatible skid steer-style carriers. It provides a prepared attachment-side interface for custom buckets, pallet-fork frames, grapples, bale attachments and specialty implements.

The reinforced steel plate has listed dimensions of 48 inches by 6 inches by 18 inches and weighs approximately 70 pounds. Those specifications help a fabricator plan the build, but they do not establish the capacity or compatibility of the finished attachment. Carrier geometry, supporting steel, weld design, attachment balance and machine limits must all be evaluated.

Buyers comparing skid steer and Euro connections can view the full selection of AG-GO quick attach plates.

Integrated Kick-Out Tabs and Weld-On Fabrication

The UQA38 includes integrated kick-out tabs designed to change the plate’s position relative to a compatible attachment. When the complete geometry is correct, these tabs can provide additional rollback angle. More rollback may help retain loose material in a bucket or improve load positioning with certain grapples, bale frames and pallet-fork attachments.

The actual rollback improvement depends on the carrier, loader linkage, plate angle and finished attachment design. The tabs do not guarantee a particular tilt range on every machine. A fabricator should check rollback, dump angle, ground contact, cutting-edge position, heel clearance and loader-arm interference before completing the build.

Typical fabrication projects include:

• New or replacement loader buckets
• Skid steer pallet-fork frames
• Brush, root or material grapples
• Bale spear and hay-handling attachments
• Equipment repairs and coupler conversions
• Custom agricultural or construction tools

The UQA38 is intended for weld-on installation. A qualified fabricator must determine the plate position, supporting structure, reinforcement, joint preparation and welding procedure for the intended load. The plate should remain square while it is fitted and welded because heat distortion or poor alignment can prevent complete engagement.

This quick attach plate does not increase the rating of an existing attachment. Safe capacity is limited by the lowest-rated component, including the skid steer, loader arms, carrier, locking wedges or pins, plate, welds and attachment structure.

Universal Skid Steer Fit and Locking Checks

“Universal” describes the common skid steer quick-attach mounting style; it does not mean the UQA38 automatically fits every skid steer, compact track loader, compact loader or tractor-loader carrier. Before fabrication, compare the upper lip, lower pin openings, locking-wedge engagement, plate width, clearance and rollback geometry.

The UQA38 is different from the EQA38 Euro quick attach plate. The EQA38 serves compatible Euro or Global tractor-loader carriers, while the UQA38 uses the skid steer-style interface. These mounting systems are not interchangeable.

Before final welding, test-position the plate on the intended carrier without lifting a load. Confirm that the top edge seats correctly, both lower locking points engage fully and the attachment rests at the intended angle. After welding and cooling, inspect for distortion, cracking, incomplete welds or interference and repeat the complete connection check.

For a general example of attachment engagement, operators can view Bobcat’s Bob-Tach attachment-change demonstration. The video is an educational reference and does not replace the operating manual or procedures for the customer’s specific machine and carrier.

Inspect the plate, upper lip, lower openings, welds, locking components and surrounding attachment steel regularly. Never operate with incomplete engagement, worn locking points, visible cracks or distortion. Confirm both sides are locked before raising, tilting or moving the attachment.

The UQA38 is manufactured in the USA at PRO-Link’s AG-GO production facility under the direction of its engineering team. Buyers who need assistance distinguishing universal skid steer and Euro mounting styles can contact PRO-Link. The plate is protected by a one-year limited warranty against manufacturer’s defects.

Questions & Answers

Does the UQA38 fit every skid steer?

No. Confirm the carrier dimensions, upper-lip engagement, lower locking points, clearances and machine requirements before welding the plate into an attachment.

What do the integrated kick-out tabs do?

When the carrier and attachment geometry are suitable, the tabs can increase rollback angle and help position or retain material. The actual change depends on the completed installation.

Does the UQA38 determine attachment capacity?

No. Capacity is controlled by the lowest-rated component in the machine, carrier, plate, welds and completed attachment.