BF2500 2,500 lb Skid Steer Bucket Forks – 42 Inch Kit

Description

The AG-GO BF2500 2,500 lb skid steer bucket forks turn a compatible loader bucket into a removable material-handling attachment for pallets, lumber, fencing supplies, landscaping materials, logs, feed, and other lighter jobsite loads. This compact bucket fork kit gives farms, acreage owners, landscapers, and contractors another way to use equipment they already own without permanently dedicating the machine to a separate pallet fork frame.

The BF2500 is the smallest-capacity model in the AG-GO bucket fork line. Its 42 inch blades and shorter shaft make it especially useful for compact equipment, smaller buckets, and jobs where maneuverability matters more than the higher ratings or longer blades offered by larger kits. The fork system carries a published 2,500 lb rating, but the actual working limit is always determined by the lowest-rated part of the complete setup.

Operators comparing bucket dimensions, fork lengths, and capacities can use PRO-Link’s bucket fork kit selection guide or review the complete line of AG-GO bucket fork kits.

Compact 42 Inch Forks with Adjustable Spacing

The BF2500 includes one matched pair of steel fork blades. Each blade measures 1.50 inches thick by 3 inches wide by 42 inches long. That profile provides practical support for standard pallets and everyday materials while keeping the attachment more manageable around barns, storage areas, landscape sites, and other locations with limited working room.

Welded bushings on the fork assemblies slide over the round shaft. The operator can position the forks along the shaft to match different pallet openings or provide balanced support beneath irregular material. Fork spacing should always be set evenly around the bucket centerline, and the load should be centered across both blades.

The complete BF2500 system includes:

• One matched pair of 42 inch fork blades
• Welded fork bushings
• A 1 inch diameter shaft up to 54 inches long
• Three heavy steel weld-on top hooks
• A large retaining washer
• A hitch pin for shaft retention

The kit is designed for compatible buckets with openings up to 32 inches. That measurement is an important starting point, but it is not the only fit requirement. Buyers should also examine bucket width, outside height, top-edge construction, steel thickness, hook clearance, cutting-edge position, and available space for the shaft and fork backs.

Machine brand alone cannot confirm fit. A compact tractor, skid steer, loader, or backhoe may be a suitable application only when its bucket geometry, structure, lifting ability, and operating limits match the kit and intended work. PRO-Link can also discuss different shaft widths or hook configurations when standard dimensions do not suit a particular bucket.

The 42 inch blades work well for loads that can remain close to the bucket, including:

• Palletized feed, seed, mulch, and landscape supplies
• Fence posts, panels, wire, and repair materials
• Lumber, firewood, logs, and bundled material
• Tools, equipment parts, and general farm supplies
• Materials being staged near barns, shops, or trailers

For operators who need a higher published rating, longer 48 inch blades, or compatibility with a larger bucket opening, the BF4500 skid steer bucket fork kit is the next model to compare.

Weld-On-Hook Installation and Safe Operation

The BF2500 is a weld-on-hook bucket fork system. During the initial installation, a qualified welder or fabricator positions and welds the three supplied hooks to the top front edge of a suitable bucket. Hook placement matters because it controls shaft alignment, fork position, clearance, and how lifting forces enter the bucket structure.

The fork assemblies slide onto the shaft through their welded bushings. The shaft is then supported by the installed bucket hooks, and the large washer and hitch pin retain the assembly. The forks themselves are not welded to the bucket.

After the hooks have been installed correctly, the operator can engage or disengage the shaft and fork assembly with controlled bucket movements. This lets the machine switch between pallet handling and normal bucket work without a hydraulic connection. Nobody should stand between the machine and attachment or beneath raised equipment during mounting, removal, or operation.

Before ordering, measure from the bucket’s cutting edge to its top outside edge and confirm the complete bucket opening. The related-company ALLPROFORKS bucket fork guide provides additional diagrams explaining bucket measurement, hook positioning, shaft engagement, and general installation steps.

The BF2500’s 2,500 lb figure is the published rating of the fork system. It does not mean every compatible machine or bucket can lift 2,500 lb. Safe capacity may be lower because of the skid steer or tractor rating, loader geometry, bucket strength, weld quality, ballast, terrain, and load position. Bucket-mounted forks place the load forward of the machine, and weight carried near the blade tips creates more leverage than weight positioned close to the bucket.

For better stability, place the heaviest part of the load near the fork backs, keep both blades evenly loaded, and carry material low while traveling. Avoid sudden turns, sharp braking, side loads, and operation across steep slopes. Allow additional stopping and turning room when carrying lumber, logs, or other long material.

Inspect the forks, bushings, shaft, hooks, washer, hitch pin, welds, and bucket before use. Stop operation if any component is bent, loose, cracked, excessively worn, or misaligned.

The BF2500 is manufactured in the USA at PRO-Link’s production facility as part of the AG-GO attachment line. It is covered by PRO-Link’s one-year limited warranty against manufacturer’s defects.

Questions & Answers

What bucket size will the BF2500 fit?

The kit is designed for bucket openings up to 32 inches. Buyers must also verify the bucket width, top-edge construction, hook area, steel thickness, and machine capacity because opening size alone does not guarantee fit.

Are the BF2500 forks permanently attached?

No. Only the three mounting hooks are welded permanently to the bucket. The shaft and fork assemblies are removable, allowing the bucket to return to digging, loading, and cleanup work.

Can the 2,500 lb skid steer bucket forks lift their full rating on every machine?

No. The 2,500 lb rating applies to the fork kit. The lowest-rated component—including the machine, loader, bucket, installation, hooks, shaft, forks, and load position—determines the safe working limit.