2A 150-4-48 Pallet Forks | Class 2, 48 inch, 5,000 lb Pair

Description

The 2A 150-4-48 are 5,000 lb 48 inch Class 2 pallet forks sold as a matched pair for a properly matched ITA carriage. Each blade measures 1 1/2 inches thick, 4 inches wide, and 48 inches long. A standard taper helps the forks enter pallet openings, while the published pair rating is 5,000 lb at a 24 inch load center. These dimensions make the model a candidate for replacing worn forks or fitting a compatible carriage when an operator needs more blade thickness than a 1 3/8 inch model.

The “2A” portion of the model identifies its Class 2A mounting clip arrangement. Class describes the spacing and geometry of the upper and lower clips; it does not determine the forklift’s lifting capacity. Verify the carriage rails, locking positions, and overall machine rating before selecting replacement forks.

What the 48 Inch Blade Provides

A 48 inch blade gives operators reach under many palletized loads, including feed, building supplies, crated equipment, and general warehouse materials. It can provide more length under a deep load than a 42 inch blade, but length does not make an unsupported load safe. Check where the load’s weight is centered and how far it extends beyond the fork tips. A load carried farther forward can reduce the capacity available from the machine and attachment.

The 4 inch width provides a bearing surface beneath the load, and the standard taper aids pallet entry when the forks are aligned with the openings. Position the pair at an appropriate spacing for the load and place the forks fully beneath it where possible. Keep the load centered and low during travel. Never use the published fork-pair rating as a substitute for the forklift’s or loader’s own capacity information.

The 2A 150-4-48 forks are made from Cr40 alloy steel. The product specifications describe extra material at the heel, where the horizontal blade curves into the upright shank. This area experiences repeated stress in service, making it an important place to inspect for wear, cracks, and deformation. The listing also describes dye penetrant inspection and a 3:1 safety factor. Those production features do not replace ongoing inspections or proper operation.

Confirm the Carriage and Pair Rating

The published 5,000 lb rating is for the pair at a 24 inch load center, not for each individual fork. If the load center changes, the machine’s usable capacity can change as well. Match the pair to the carriage class, the actual load, and the lowest rated component in the lifting system. Check that both fork locks engage, the clips seat correctly on the rails, and the forks can be positioned as required for your pallets.

This model’s code gives a dimension check: “150” denotes 1 1/2 inch thickness, “4” denotes 4 inch width, and “48” denotes 48 inch blade length. If a shorter blade better suits your work, compare the 2A 150-4-42 Class 2 forks. For other lengths and blade sizes, browse PRO-Link’s ITA pallet forks. Match the forks you order to the actual carriage and equipment rather than relying on a similar-looking model number.

These forks are sold only in pairs and are covered by PRO-Link’s one-year limited warranty against manufacturing defects, subject to its terms. Before each shift, inspect the heels, tips, mounting clips, locks, and blade surfaces. Remove damaged forks from service and follow the equipment manufacturer’s inspection and replacement guidance.

Questions About the 2A 150-4-48

Is the 5,000 lb rating for one fork?

No. The published rating applies to the matched pair at a 24 inch load center. The machine or carriage may impose a lower limit.

Will these fit any Class 2 forklift?

Not necessarily. Verify the Class 2A clip geometry, carriage rails, fork locks, and machine limits before ordering.

What changes compared with the 42 inch version?

This model has 48 inch blades; the 2A 150-4-42 has 42 inch blades. Choose the length that supports your loads within the equipment’s limits.