110T 1.375 Inch Tapered Spear Sleeve – Conus I

The HAYSTIX® 110T 1.375 inch tapered spear sleeve is a Conus I weld-in collar for mounting specified PRO-Link bale spears in a properly designed agricultural frame. Its machined internal taper provides the matching seat for the spear shank and helps keep the tine aligned. The sleeve can be used for new attachment fabrication or to replace a damaged collar in an existing hay-handling frame.

This listing is for the 110T sleeve only; the spear, retaining hardware, frame, and welding are separate. Buyers who need a complete tine-and-sleeve package should select the appropriate assembly from the HAYSTIX® 1 3/8 inch bale spear collection. Match the exact spear model and mounting profile before ordering because nominal diameter alone does not establish fit.

Matching the 110T to Conus I Bale Spears

The 110T is the verified sleeve supplied with these complete HAYSTIX® assemblies:

• 336CXJ curved bale spear
• 336TXJ 33 inch tapered spear
• 396TXJ 39 inch tapered spear
• 436TXJ 43 inch tapered spear

Each listed non-S assembly includes the matching sleeve and retaining hardware. The corresponding product number beginning with “S” identifies a spear-only replacement. Reusing an installed 110T is appropriate only when the collar, surrounding steel, welds, taper, and clearance remain serviceable.

A similar outside diameter does not make another tine compatible. Confirm the Conus I shank shape, seating depth, threads, retaining nuts, and mounting dimensions. The 110T uses a tapered nut-retained connection, not a straight cross-bolt system. Cross-bolt components require aligned holes and should not be substituted for this collar. The HAYSTIX® bale spear hardware section can help buyers compare sleeves, nuts, brackets, and other mounting parts.

With the correct spear, the tapered shank seats inside the 110T. The applicable conical nut draws the matching surfaces together, and the jam nut locks against it to help resist vibration-related loosening. The Doublenut® bale spear mounting system guide explains the connection and inspection points. This hardware does not eliminate routine checks or make mismatched parts safe.

Weld-In Installation and Frame Checks

The empty 110T collar must be welded into suitable steel tubing or another properly engineered mounting location. Remove the spear and retaining hardware before welding. A qualified fabricator should determine sleeve direction, projection, alignment, supporting steel, joint preparation, welding procedure, and completed frame strength. Accurate placement is especially important in a multi-tine attachment because uneven projection or alignment can prevent the spears from sharing the load as intended.

Allow the frame to cool before installing the tine. Inspect the sleeve opening and remove dirt, corrosion, weld spatter, or debris that could prevent full taper engagement. The spear should seat without binding, visible looseness, or thread interference. After securing the correct hardware, verify tine alignment, operating clearance, weld condition, and frame integrity before use.

The 110T may be incorporated into compatible tractor front-end loader, skid steer, telehandler, 3 point bale mover, or custom agricultural frames. These are possible applications, not universal fit claims. The collar does not determine attachment capacity. Safe operation depends on the complete system, including the spear, hardware, welds, frame, coupler, tine spacing, load center, ballast, and carrier limits.

Inspect the collar, spear, nuts, surrounding tubing, and welds regularly. Stop using the attachment if the sleeve is cracked, distorted, loose, badly worn internally, or unable to hold the spear correctly. The 110T is covered by PRO-Link’s one-year limited warranty against manufacturer’s defects, subject to the complete warranty terms.

Questions & Answers

Which PRO-Link bale spears use the 110T sleeve?

The 110T is the verified Conus I collar for the 336CXJ, 336TXJ, 396TXJ, and 436TXJ complete assemblies. Confirm the exact spear model and mounting profile before ordering.

Is the 110T a weld-in spear sleeve?

Yes. A qualified fabricator welds the empty collar into suitable supporting steel. Remove the spear and retaining hardware before welding, then allow the frame to cool and inspect the installation before assembly.

Will any 1.375 inch bale spear fit the 110T?

No. Match the Conus I taper, shank dimensions, threads, seating depth, nut arrangement, and installation clearance. Diameter alone cannot confirm compatibility.