49FXJ 49-Inch Fluted Bale Spear with 144T Sleeve

The HAYSTIX® 49FXJ 49-inch fluted bale spear is a complete tapered spear-and-sleeve assembly for heavy hay-handling attachments. It combines a 49-inch by 1.75-inch fluted tine with the matching 144T weld-in sleeve and nut-retention hardware. The spear carries a published capacity of 3,500 pounds at a 30-inch load center, giving farmers, ranchers, feedlots, and equipment builders a dependable option for moving large round bales and dense square bales.

Unlike a straight cross-hole spear, the 49FXJ uses a tapered mounting end. The taper seats inside the 144T collar, and the nuts draw the spear firmly into position after the sleeve has been welded into a suitable frame. This complete configuration works well for new fabrication and for repairs where both the tine and its mounting sleeve need to be replaced.

Fluted Profile for Dense Bale Material

The 49FXJ is the fluted exception in the HAYSTIX® 1.75-inch product family. Its shaped profile helps the point work progressively into tightly packed hay rather than forcing the full shaft width into the bale at once. That can support smoother insertion and withdrawal when handling dense hay, straw, silage, haylage, or cornstalk bales.

At 49 inches long, the spear provides deep engagement in properly sized bales. The added reach can help the attachment maintain contact while a bale is lifted, carried, stacked, placed in a feeder, or unloaded from a trailer. Bale control still depends on correct spear spacing, frame design, machine angle, travel speed, terrain, and the location of the load. Operators should keep the bale low during travel and avoid sudden turns or stops.

The 3,500-pound figure is the published working capacity for the individual spear at a 30-inch load center. Although PRO-Link has performed higher-load testing on 1.75-inch bale spears, testing above the published rating does not change the product capacity. Customers and operators should use 3,500 pounds as the maximum published spear rating and must also follow the lowest rating of the frame, coupler, loader, and carrying machine.

144T Weld-In Sleeve and Tapered Installation

The included 144T sleeve is designed to be welded into suitable steel tubing or another properly supported location in a bale-spear frame. The spear and nuts must be removed before welding. A qualified fabricator should determine the sleeve direction, projection, alignment, supporting steel, and correct welding procedure for the finished attachment.

After the collar and frame have cooled, the tapered end of the spear slides into the matching 144T seat. Tightening the applicable nut hardware pulls the mating surfaces together and holds the tine in its installed position. This is different from a cross-bolt assembly, where a bolt passes through aligned holes in a straight spear and sleeve. Buyers should confirm the 49FXJ model, fluted profile, 1.75-inch size, taper, and 144T collar before mixing it with existing components.

When built into a properly engineered carrier, this 49-inch fluted bale spear may be used on hay attachments for tractor front-end loaders, skid steers, telehandlers, bale movers, or other suitable agricultural machines. It is not a direct-fit attachment for every machine. Actual compatibility depends on the frame, sleeve placement, spear spacing, quick-attach coupler, operating clearances, welds, and complete equipment capacity.

Inspect the point, shaft, flutes, tapered mounting end, threads, nuts, 144T sleeve, welds, and surrounding frame before use. Stop operating if any component is loose, bent, cracked, distorted, or excessively worn. The 49FXJ is covered by PRO-Link’s one-year limited warranty against manufacturer’s defects, subject to the complete warranty terms.

Questions & Answers

What capacity should be used for the 49FXJ?

Use the published rating of 3,500 pounds at a 30-inch load center. Higher test loads do not raise the working capacity of the spear or the completed attachment.

What parts are included with this 49-inch fluted bale spear?

The 49FXJ includes the 49-inch by 1.75-inch tapered fluted spear, matching 144T weld-in sleeve, and applicable nut-retention hardware.

Will the 49FXJ fit any tractor or skid-steer bale frame?

No. The sleeve must be welded into a compatible, properly designed frame. Verify the tubing, collar position, spear spacing, coupler, clearances, weld strength, and all equipment ratings before